-
نشریه مواد پرانرژی
مواد پرانرژی
Engineering & Technology
http://isaem.ir
1
admin
1735-3629
-
-
-
-
-
-
fa
jalali
1399
9
1
gregorian
2020
12
1
15
1
online
1
fulltext
fa
بررسی اثر مهار جانبی اِستادهای دیوار بر روی تابع مقاومت ایستایی اِستادها تحت بار انفجار
سازه های مقاوم به انفجار
سازه های مقاوم به انفجار
پژوهشي
Research
<em>«اِستاد وال­های سرد نورد فولادی» از گزینه­های نوین ساخت دیوار در ساختمان­سازی بشمار می­روند. اسکلت اصلی این دیوارها از تعدادی عضو قائم (اِستاد) تشکیلشده است که معمولاً در بالا و پایین خود در داخل دو عضو افقی (تِرَک) مهار می­شوند. یکی از راه­های تحلیل و طرح اِستاد­های دیوار، به­عنوان عضو مقاوم خمشی تحت بار انفجار، استفاده از تابع مقاومت ایستایی اِستاد­ها است. این تابع در تحلیل­های دینامیکی دیوار تحت بار انفجار، جایگزین سختی اعضای باربر می­گردد و امکان ساده­سازی به یک سیستم تک درجه آزادی را فراهم می­سازد. به­منظور امکان استفاده از ظرفیت خمشی اِستادها، تأمین مهار جانبی مناسب برای آ­ن­ها امری ضروری است. در غیر این صورت، کمانش جانبی-پیچشی در اِستادها پیش از استفاده از ظرفیت خمشی عضو، مانع از شکل­گیری مکانیسم مقاوم در این اعضا می­گردد. نظر به توضیحات ارائهشده، این پژوهش به بررسی اثر مهار جانبی در مقاومت تحت بار انفجار اِستاد­های دیوار می­پردازد. در این راستا با استخراج تابع مقاومت ایستایی اِستادها در یک نمونه اِستاد وال مرسوم به کمک تحلیل­های المان محدود، حداقل تعداد مهار جانبی و فاصله بهینه قرارگیری مهارها تعیین شده است. بر این اساس استفاده از دو پُل به­عنوان مهار جانبی، در فاصله تقریبی حدود یکپنجم میان دهانه، به­عنوان حالت بهینه مهار جانبی تحت فشار معادل بار انفجار بدست آمد.</em>
“Cold-formed steel (CFS) stud walls” are innovative alternative for construction of walls in buildings. The main frames of CFS walls consist of a group of vertical members called “studs” which are hold by fasteners within two horizontal members called “tracks” at the upper and lower ends. One of the conventional ways for designing and analyzing of CFS stud walls under blast loading is to employ proper “static resistance functions” of studs. These functions, as the representative of system resistance, permit simplification of CFS stud walls into an equivalent single degree of freedom system for further dynamic analyses under blast loading. Providing adequate lateral bracing is a vital measure to make use of studs’ flexural resistance. If not, lateral-torsional buckling of studs prevent from full utilization of their flexural resistance and subsequent tension-membrane resisting mechanism. Therefore, this study deals with the effect of lateral bracing of studs on the expected resistance of walls exposed to the blast pressure waves. To this end, by adopting a portion of a conventional stud wall and performing finite element analyses, the minimum required bracings and their optimum positions have been determined. Accordingly, make use of two bridges at middle fifth of the stud wall’s span was found as the optimum alternative for the lateral bracing under equivalent blast pressure.
اِستاد وال سرد نورد فولادی, بار انفجار, تابع مقاومت ایستایی, مهار جانبی, تحلیل المان محدود
Cold-formed steel stud wall, Blast loading, Static resistance function, Lateral bracing, Finite element analysis
27
37
http://isaem.ir/browse.php?a_code=A-10-1818-1&slc_lang=fa&sid=1
Alireza
Moazezi Mehretehran
علیرضا
معززی مهر طهران
a.moazezi@student.sharif.edu
100319475328460011808
100319475328460011808
Yes
Sharif University of Technology
دانشگاه صنعتی شریف
محمد
مهدی پور
Mo12348@yahoo.com
100319475328460011809
100319475328460011809
No
دانشگاه صنعتی مالک اشتر