-
نشریه مواد پرانرژی
مواد پرانرژی
Engineering & Technology
http://isaem.ir
1
admin
1735-3629
-
-
-
-
-
-
fa
jalali
1392
6
1
gregorian
2013
9
1
8
1
online
1
fulltext
fa
پیش بینی رفتار پیش و پسا-گسیختگی ورقهای دایرهای تحت بارهای دفعی با استفاده از تحلیلهای حدی تغییر شکل (علمی-پژوهشی)
ضربه
ضربه
پژوهشي
Research
دو مدل شبه – استاتیکی موثر برای بررسی رفتار پیش و پسا-گسیختگی ورقهای دایرهای گیردار تحت بارگذاری دفعی بر پایه تحلیلهای حدی کرانه بالای تغییر شکل ارایه می گردد. در مدل اول، با فرض داشتن پروفیل نهایی به صورت یک مخروط که توسط حرکت شعاعی و عمودی یک مفصل تنهای پلاستیک محیطی در نوردیده است، خیز دائمی در حالت قبل از گسیختگی موضعی محاسبه می شود. در مدل دوم، با فرض تشکیل پروفیل نهایی به صورت گنبدی شکل، ساز و کار تغییر شکل از چندین مفصل محیطی با توزیع یکنواخت یا غیر یکنواخت ناشی می شود. در این بخش حرکت بعد از جدایش ورق در لحظه ای که گسیختگی موضعی رخ می دهد نیز به حساب آورده می شود. با محاسبه انرژیهای تغییر شکل پلاستیک، خیز دائمی قبل از جدایش محاسبه شده و تاثیر تعداد و توزیع مفصلها بررسی می گردد. از آنجاییکه مقدار سرعت باقیمانده پس از جدایش می تواند نقش مهمی را در تصدیق درستی یک تخمین شبه - استاتیکی تغییر شکل در آستانه گذر از مود اول به دوم شکست ایفا کند، بنابراین با داشتن مقادیر انرژی مربوطه، مقدار این سرعت بدون نیاز به تحلیل دینامیکی برآورد می گردد. در نهایت با مقایسه نتایج بدست آمده از مدلهای ارایه شده با سایر کارها نظری و داده های آزمایشگاهی دیگران مطابقت خوب نتایج مشاهده می گردد.
Two effective quasi – static models are presented to consider pre and post- failure behaviors of the clamped circular plates subjected impulsive loads based on upper bound limit analyses of deformation. In first model, it is assumed that final profile is considered to have a conical shape, which is represented by radial and vertical motions of a single peripheral plastic hinge permanent deflection is calculated before local failure. In second model, supposing the final deformation is as a dome shape, mechanism of deformation is caused by multi- peripheral stationary hinges with uniform or non- uniform distribution. In this part, motion after severance of the plate is considered at the instance that the local failure is occurred. Calculating plastic deformation energies, permanent deflection before the severance is computed and influence of number and distribution of hinges are considered. Since, value of residual velocity after tearing can perform principle role for validation of a quasi static estimation of the deformation at transit threshold from the first failure mod into second one. So, having amounts of relevant energies, value of this velocity is evaluated without needing to dynamic analysis. Finally, by comparisons between obtained results from introduced models and other works and experimental data, good agreements of them are observed.
بار دفعی، ورق دایره ای، مفصل پلاستیک، گسیختگی موضعی برشی، انرژی جنبشی باقیمانده
Impulsive load, Circular plate, Plastic hinge, Local shear failure, Residual kinetic energy
59
75
http://isaem.ir/browse.php?a_code=A-10-617-1&slc_lang=fa&sid=1
Asghar
Zajkani
اصغر
زاجکانی
azajkani@gmail.com
10031947532846003677
10031947532846003677
Yes
Department of Mechanical Engineering, Engineering Faculty, University of Guilan
دانشگاه گیلان، دانشکده فنی، بخش مهندسی مکانیک
Abolfazl
Darvizeh
ابوالفضل
درویزه
azajkani@gmail.com
10031947532846003678
10031947532846003678
No
Department of Mechanical Engineering, Islamic Azad University- Bandar Anzali branch, Bandar Anzali, Iran
دانشگاه آزاد اسلامی، واحد بندر انزلی، بخش مهندسی مکانیک
Mansour
Darvizeh
منصور
درویزه
azajkani@gmail.com
10031947532846003679
10031947532846003679
No
ical Engineering, Engineering Faculty, University of Guilan
دانشگاه گیلان، دانشکده فنی، بخش مهندسی مکانیک
رضا
انصاری خلخالی
azajkani@gmail.com
10031947532846003680
10031947532846003680
No
دانشگاه گیلان